Microstructure,texture,and mechanical properties of the extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy were investigated at different extrusion temperatures(260 and 320℃),extrusion ratios(10:1,15:1,and 30:1),and extrusion speeds(3 and 6 mm/s).The experimental results exhibited that the grain sizes after extrusion were much finer than that of the homogenized alloy,and the second phase showed streamline distribution along the extrusion direction(ED).With extrusion temperature increased from 260 to 320℃,the microstructure,texture,and mechanical properties of alloys changed slightly.The dynamic recrystallization(DRX)degree and grain sizes enhanced as the extrusion ratio increased from 10:1 to 30:1,and the strength gradually decreased but elongation(EL)increased.With the extrusion speed increased from 3 to 6 mm/s,the grain sizes and DRX degree increased significantly,and the samples presented the typical<2111>-<1123>rare-earth(RE)textures.The alloy extruded at 260℃ with extrusion ratio of 10:1 and extrusion speed of 3 mm/s showed the tensile yield strength(TYS)of 213 MPa and EL of 30.6%.After quantitatively analyzing the contribution of strengthening mechanisms,it was found that the grain boundary strengthening and dislocation strengthening played major roles among strengthening contributions.These results provide some guidelines for enlarging the industrial application of extruded Mg-RE alloy.
Chenjin ZhangGuangyu YangLei XiaoZhiyong KanJing GuoQiang LiWanqi Jie
The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.
Jian-xing ZHAOChao-wei ZENGTing YUANWei PENGZhen-wei SUNOu ZHANGHong-jun HU
Mg-1.2Y-1.2Ni(at.%)alloy was extruded at 400℃with an extrusion ratio of 16:1 and different rates from 1 to 6 mm/s.The effect of extrusion rate on microstructure and mechanical properties of the Mg-1.2Y-1.2Ni alloy was systematically investigated.With the increase of extrusion rate,the average recrystallized grain size of Mg-1.2Y-1.2Ni alloy and mean particle diameter of Mg2Ni phase were increased,while the density of geometrically necessary dislocation and the intensity of the basal texture were decreased.When extrusion rate increases from 1 to 6 mm/s,the tensile yield strength(TYS)of asextruded Mg-1.2Y-1.2Ni alloy decreases from 501 to 281 MPa,while the elongation to failure increases from 1.5%to 6.2%.The Mg-1.2Y-1.2Ni alloy extruded at 3 mm/s obtained TYS of 421 MPa,the ultimate tensile strength(UTS)of 440 MPa and elongation to failure of 2.6%,respectively,exhibiting comprehensive mechanical properties with relatively good plasticity and ultrahigh strength.The ultrahigh TYS of 501 and 421 MPa was mainly due to the strengthening from ultrafine recrystallized grains,high volume fraction long period stacking ordered(LPSO)phases and high density dislocations.
