Work hardening is a well-known phenomenon occurring in crystalline metals during deformation,which has been widely used to increase the strength of metals although their ductility is usually reduced simultaneously. Here we report that the plastic strain of Zr41Ti14Cu12.5Ni10Be22.5 (at.%) bulk metallic glasses has been increased from 0.3% for the as-cast sample to 2.5%-8.0% for samples that have experienced pre-deformation under constrained conditions. The pre-deformed glassy alloys possess more free volume and abundant introduced shear bands,which are believed to promote the activation of shear bands in post-deformation and result in an increase in plasticity. The orientation of the pre-introduced shear bands relative to the loading direction will affect the deformation behavior of pre-deformed samples. The present results show that pre-deformation of this glassy alloy will result in work toughening. This work toughening effect can be removed by isothermal annealing at a sub-Tg (glass transition) temperature,which causes annihilation of free volume and healing of shear bands.
The Zr41Ti14Cu12.5Ni10Be22.5 (at.%) bulk metallic glass composites with various crystallization fractions were prepared by pretreating the bulk metallic glassy samples with pulsing current, and then by isothermal annealing at near initial crystallization temperature for different periods of time. The precipitations and crystallization fractions were studied by X-ray diffraction (XRD) and differential scanning calorimetry (DSC), and their effects on mechanical properties of the composite were studied by microhardness, uniaxial compression test and scanning electron microscopy (SEM). The experimental results show that the primary precipitate is quasicrystalline phase and other metastable phases including Be2Zr, Zr2Cu and FCC would precipitate subsequently. In the initial crystallization process, in which the crystallization fraction increases from 0 to 8.2%, both fracture strength and plastic strain increase, with the maximum plastic strain up to 6.4%. When the crystallization fraction is larger than 8.2%, the fracture strength and the plastic strain decrease sharply. Furthermore, the alloy with low crystallization fraction is fractured by shearing, while for high crystallization fraction it is fractured by splitting and cleavage. The results show that the mechanical properties of the glassy alloy could be optimized by controlling the processing parameters.
QIU ShengBao1,2, YAO KeFu1 & GONG Pan1 1 KLAMPT, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
The effect of atomic oxygen(AO) on the surface oxidation of several typical Cu-based bulk metallic glasses(BMGs) was studied in the present work.The AO source using in this study is generated by discharge plasma type ground simulation equipment.The AO erosion/oxidation resistances of the amorphous alloy samples were assessed based on the analysis of mass loss,surface color and microstructure.It is found that these Cu-based BMGs possess good AO erosion/oxidation resistance and their resistance to AO erosion/oxidation strongly depends on the chemical composition.For the samples containing more Ag and/or Cu,the AO erosion/oxidation resistance is weaker.The present result is important for designing new metallic glasses using as space materials.
A series of Ti-Zr-Be-Fe bulk metallic glasses(BMGs)with good glass-forming ability(GFA)and high specific strength have been developed.With different alloying routes and content of Fe,it is found that these alloys exhibit different GFA and mechanical properties.The effects of Fe addition on the GFA and mechanical properties of Ti-Zr-Be alloy are systemically investigated.The possible mechanisms for the improvement or damage to the GFA by addition of Fe can be interpreted in view of the mixing enthalpy,atomic size differences and electronegativity differences of the alloys,while the mechanical properties strongly depend on the Poisson’s ratio and free volume concentration.The experimental results also show that alloying technology is an effective method to improve the GFA and mechanical properties of Ti-Zr-Be glassy alloy.
Fe-based amorphous alloys with high iron content of 76at%-80at%were synthesized in the Fe-Mo-Si-P-C-B alloy system by the single roller melt-spinning technique.The amorphous ribbons exhibit high Vickers microhardness and good ductility,which can be indented and bent 180°without breaking.A number of shear bands could be observed around the indents and the bending traces.Studies on the magnetic properties of the amorphous alloys show that they possess high saturation magnetizations of 1.34-1.6 T,which increases with the increase of iron content.The core losses of these Fe-based amorphous alloys at various magnetic inductions were tested and found to be significantly dependent on their components.The Fe-Mo-Si-P-C-B amorphous alloys with excellent mechanical properties and soft magnetic properties have promising potential in functional applications.
With the addition of Si to replace some P,Pd40.5Ni40.5SixP19-x（x=0,2.5,5,9.5,14,and 19 in atomic number fraction） bulk glassy samples with the diameter of about 5 mm were successfully prepared by use of flux treatment and water quenching technology.With the increase of Si content,the glass forming ability of Pd40.5Ni40.5Si-xP19-x increases first for low Si content and then decreases for high Si content （Si≥9.5at%）.The Pd40.50Ni40.5Si5P14 glassy alloy possesses the largest supercooled liquid region△T of 119 K,the largest reduced glass transition temperature of 0.621,and the largestγparameter of 0.460,indicating that this glassy alloy possesses very large glass forming ability and very high thermal stability.
