您的位置: 专家智库 > >

解焕阳

作品数:5 被引量:17H指数:3
供职机构:上海交通大学更多>>
发文基金:国家自然科学基金国家教育部博士点基金更多>>
相关领域:金属学及工艺一般工业技术更多>>

文献类型

  • 4篇期刊文章
  • 1篇学位论文

领域

  • 5篇金属学及工艺
  • 1篇一般工业技术

主题

  • 3篇电塑性
  • 3篇塑性
  • 2篇塑性成形
  • 1篇电脉冲
  • 1篇电塑性效应
  • 1篇先进高强钢
  • 1篇脉冲电流
  • 1篇镁合金
  • 1篇解析模型
  • 1篇回弹
  • 1篇合金
  • 1篇高强度板
  • 1篇高强钢
  • 1篇包边
  • 1篇THROUG...
  • 1篇AZ31B
  • 1篇MAGNES...
  • 1篇MICROS...
  • 1篇冲压
  • 1篇冲压工

机构

  • 5篇上海交通大学

作者

  • 5篇解焕阳
  • 4篇董湘怀
  • 2篇王倩
  • 2篇方林强
  • 1篇彭芳
  • 1篇刘凯
  • 1篇周雪

传媒

  • 1篇上海交通大学...
  • 1篇热加工工艺
  • 1篇塑性工程学报
  • 1篇Transa...

年份

  • 2篇2015
  • 1篇2013
  • 2篇2012
5 条 记 录,以下是 1-5
排序方式:
Electroplastic effect in AZ31B magnesium alloy sheet through uniaxial tensile tests被引量:2
2015年
The electroplastic effect in AZ31B magnesium alloy sheet was investigated through uniaxial tensile tests. In order to show the athermal effect of the electrical pulses, two types of uniaxial tensile tests at the same testing temperature were carried out: uniaxial tension in environmental cabinet and uniaxial tension with electrical pulses. In addition, the distribution of temperature field in the cross-section area during uniaxial tension with electrical pulses was simulated. The results show that the distribution of temperature field along the cross-section area is homogeneous. By comparing the true stress?true strain curves of AZ31B alloy under uniaxial tensile tests, the athermal effect with electrical pulses was confirmed. The microstructure evolution after the uniaxial tension was studied by optical microscopy. The results indicate that the electrical pulses induced dynamic recrystallization plays an important role in the decrease of flow stress. Finally, a flow stress model of AZ31B sheet taking the influence of electroplastic effect into account was proposed and validated. The results demonstrate that the calculated data fit the experimental data well.
解焕阳王倩彭芳刘凯董湘怀王建峰
电塑性效应及在塑性成形中的应用新进展被引量:10
2012年
分析了电塑性效应的影响因素和机理,讨论了电塑性效应在塑性成形中的应用,特别对电塑性效应在微成形和渐进成形等塑性成形工艺中的应用作出了展望,为电塑性效应在塑性成形中的广泛应用提供参考.
解焕阳董湘怀方林强
关键词:电塑性效应脉冲电流塑性成形
DP980高强度板电塑性弯曲回弹规律实验研究被引量:5
2013年
高强度钢板冲压成形后的回弹问题是其应用中的主要问题之一。电塑性成形技术可以显著改善高强钢的成形性。以V形件为研究对象,通过改变电参数,对DP980双相高强钢在电塑性成形工艺下的回弹进行了研究。结果表明:随着充电电压和脉冲频率的增加,回弹减小量增加;弯曲时通电比冷弯后通电对回弹的抑制更明显。
周雪董湘怀解焕阳
关键词:回弹
镁合金及先进高强钢电脉冲辅助塑性成形性能研究
近年来为满足汽车轻量化的要求,使用镁合金、先进高强度钢(Advanced High Strength steel,AHSS)等轻型材料来制造汽车零部件越来越受到各大车企的重视。然而,镁合金为密排六方的晶格结构,室温塑性变...
解焕阳
关键词:镁合金冲压工艺
基于功平衡原理的滚压包边力计算模型
2012年
根据滚压包边工艺中板料塑性变形的特点,对平面直边滚压包边过程进行分析,建立了平面直边滚压包边过程的简化解析模型;基于功平衡原理,推导了一个滚压包边过程中包边力的计算公式;计算结果与实际生产接近,且具有上限性质。
方林强董湘怀解焕阳王倩
关键词:解析模型
共1页<1>
聚类工具0